IP3M-941/IP2M-841E/IP3M-HX2 Firmware Release

Have some questions or having issues with your IP Camera(s), Post them here for the mods and other users to assist you with.
ScottW1
Posts: 1
Joined: Fri Oct 11, 2019 2:46 pm

Re: IP3M-941/IP2M-841E/IP3M-HX2 Firmware Release

Postby ScottW1 » Fri Oct 11, 2019 3:20 pm

I just found this forum and registered to share my experience with the new firmware.

I upgraded (1) of my (8) IP3M-941's to the new firmware. Ran into some minor problems with PTZ, and after trying some workarounds decided to "downgrade" back to old firmware (I had a copy on my PC). The downloaded files don't say anything about not being able to downgrade, and I hadn't been on the forum to see the warning at top of this thread.

The "downgrade" appeared to go just fine, but the camera didn't reboot. Solid red light on back. Powered off, back on, solid red light -- no movement, no network connection. Held button 30 seconds - nothing. Held button while powering on, got a few flashes of the red light, but nothing further. Tried multiple power cycles and hard resets, no response -- just a solid red light. CAMERA IS DEAD.

I RECOMMEND HEEDING THE WARNING IN POST #1 OF THIS THREAD, AND DO NOT ATTEMPT TO DOWNGRADE THE FIRMWARE. The camera I tried that on is now in the TRASH. :-(

As to the rest of my experience with the new firmware....

#1. The old firmware positioned the camera to preset #1 after reboot or power cycle. The new firmware seems to position the camera to the "last position set using PTZ jog controls" -- even if a preset was chosen after that. Would like to see the old behavior restored in a future version, i.e., go to preset #1 on reboot or power cycle. (There is a workaround for this in BlueIris, using the "Watchdog" function to select preset#1 on signal restoration.)

#2. I had terrible PTZ delay, overshoots, and some trouble setting presets when using EDGE browser. Switched to CHROME and had none of those problems. Using Chrome, I was able to set/delete presets reliably, they were retained after reboot, video and PTZ were very responsive.

#3. PTZ presets and jogging initially did not function at all from BlueIris. Changing the BlueIris setting for PTZ type from "Amcrest" to "Amcrest/Dahua" resolved that. Using the new setting, PTZ jogging and presets worked perfectly from BlueIris and were just as responsive as with old firmware.

#4. Really like the UI being native in browser (javascript)! Will be glad to ditch the plugin!

User avatar
Revo2Maxx
Posts: 250
Joined: Sat Jun 15, 2019 3:05 pm

Re: IP3M-941/IP2M-841E/IP3M-HX2 Firmware Release

Postby Revo2Maxx » Fri Oct 11, 2019 4:25 pm

@ScottW1 Hello and welcome to the Forum.

Thank you for sharing your thoughts and things about the firmware with others. Future I take all Trash Cameras lol JK.... To bad I wasn't in the can when you tossed it. I like to take things apart
A Lie is a Lie, no matter how big or Small. The Truth will set you Free
Secure you & your Future be Safe

James

[email protected]
Posts: 10
Joined: Sat Nov 10, 2018 1:52 pm

Re: IP3M-941/IP2M-841E/IP3M-HX2 Firmware Release

Postby [email protected] » Sat Oct 12, 2019 10:01 am



The "downgrade" appeared to go just fine, but the camera didn't reboot. Solid red light on back. Powered off, back on, solid red light -- no movement, no network connection. Held button 30 seconds - nothing. Held button while powering on, got a few flashes of the red light, but nothing further. Tried multiple power cycles and hard resets, no response -- just a solid red light. CAMERA IS DEAD.

I RECOMMEND HEEDING THE WARNING IN POST #1 OF THIS THREAD, AND DO NOT ATTEMPT TO DOWNGRADE THE FIRMWARE. The camera I tried that on is now in the TRASH. :-(
Thanks

[email protected]
Posts: 10
Joined: Sat Nov 10, 2018 1:52 pm

Re: IP3M-941/IP2M-841E/IP3M-HX2 Firmware Release

Postby [email protected] » Sat Oct 12, 2019 10:09 am

@[email protected]


We do not have any updates, We are focusing at this time on updating other models to the JS platform so other customers can regain access on Mac and also resolve some security issues. The engineering team knows of the issue and it is in the plans to optimize the FW once other major devices are updated.
Thanks, i do have a IP4M-1055E so would be great to know when JS will be available so i can unload the Chrome plugins workaround

Also - have another issue to report. Since i upgraded to the new F/w (JS Platform), the log shows that the NVR logging on and off on the camera every 1 sec. The camera sometimes is getting overwhelmed and crashes. I have a DAHUA NVR. Note that with the old firmware, i was able to setup the camera in the NVR 2 ways: 1) ONVIF via RTSP 554 & HTTP 80 and 2) Private via TCP 37777. with the new JS f/w, i can only use ONVIF. if i try Private , the NVR will not authenticate so seems that TCP 37777 has been disabled?

Note sure if anyone else has seen the multiple login / logout in the camera log...?...

zante
Posts: 2
Joined: Sat Oct 12, 2019 11:29 pm

Re: IP3M-941/IP2M-841E/IP3M-HX2 Firmware Release

Postby zante » Sat Oct 12, 2019 11:50 pm

Hello, I have the latest firmware installed on my Amcrest IP2M-841b Amcrest_IPC-AWXX_Eng_N_AMCREST_V2.420.AC00.18.R.20190803 Now my Chrome browser takes much longer to display the image.

The second major problem is that there is no timeline in the playback. Is the latest software not suitable for the 841 b?
Screenshot: https://www.bilder-upload.eu/bild-14307 ... 2.jpg.html

Can I go back to the old software?

longedge
Posts: 214
Joined: Fri Mar 31, 2017 9:34 am

Re: IP3M-941/IP2M-841E/IP3M-HX2 Firmware Release

Postby longedge » Sun Oct 13, 2019 1:00 am

@zante Hello and welcome to the forum. I held back from installing the update on my IP2M-841B camera because, as you can see it isn't listed in the models for which the firmware was released. I don't know what the exact differences are between the IP2M-841B and IP2M-841E apart from the latter is a PoE camera but since you've already done the update, the clear warnings about not going back to the old firmware are what matters.

It's very clear from the first post in this thread that re-installing older firmware can break the camera so it's at your own risk as far as I can see :) .
Cameras -
One IP2M-841B on firmware 2.520.AC00.18.R
Two IP3M-941B on firmware 2.620.00AC003.3.R

zante
Posts: 2
Joined: Sat Oct 12, 2019 11:29 pm

Re: IP3M-941/IP2M-841E/IP3M-HX2 Firmware Release

Postby zante » Sun Oct 13, 2019 2:19 am

@longedge, thank you for your answer!! I have found this new firmware on the download page Amcrest and here is the FW that is suitable for the IP2M-841b - I've never had a problem with upgrading a new Fw just now. Makes me unhappy I still wanted to buy several cams from Amcrest, of course not now because of this experience.
https://www.bilder-upload.eu/bild-196d1 ... 4.jpg.html


Return to “IP Cameras”

Who is online

Users browsing this forum: Google [Bot] and 11 guests