I don't understand, on the back of the doorbell it clearly says 16- 24 volts 0.5 amps. So where does the 2 amps come from?
Search found 9 matches
- Fri Jul 30, 2021 3:53 am
- Forum: IP Cameras
- Topic: New AD410 doorbell dies within 5 minutes
- Replies: 34
- Views: 22093
- Thu Jul 29, 2021 3:20 pm
- Forum: IP Cameras
- Topic: New AD410 doorbell dies within 5 minutes
- Replies: 34
- Views: 22093
Re: New AD410 doorbell dies within 5 minutes
Hi James, I first tried this one but unfortunately without success https://www.vekto.nl/voeding-12vdc-15w-1-25a-dinrail-ingang-85-264vac . Then I connected this https://www.vekto.nl/beltrafo-8-24vac-24va-met-schakelaar but unfortunately also nothing. The doorbell only turns on with the 5v USB cable ...
- Sat Jul 17, 2021 11:33 am
- Forum: IP Cameras
- Topic: New AD410 doorbell dies within 5 minutes
- Replies: 34
- Views: 22093
Re: New AD410 doorbell dies within 5 minutes
I did the skip thing after i did a hard reset with the 5v usb micro connected. After setting up including the skip thing everything works perfect. But when i disconnect the 5v usb and connect the 24v on the back screws the doorbell dont starting. Everything stays black/dead. When i replace my Ezviz ...
- Sat Jul 17, 2021 8:00 am
- Forum: IP Cameras
- Topic: New AD410 doorbell dies within 5 minutes
- Replies: 34
- Views: 22093
Re: New AD410 doorbell dies within 5 minutes
With the 5v all goes well with the 24v on the connection on the back the doorbell does nothing anymore.
- Sat Jul 17, 2021 6:28 am
- Forum: IP Cameras
- Topic: New AD410 doorbell dies within 5 minutes
- Replies: 34
- Views: 22093
Re: New AD410 doorbell dies within 5 minutes
I put a 5v micro usb and the device is still working!
I did a hard reset and will try further.
I did a hard reset and will try further.
- Sat Jul 17, 2021 6:16 am
- Forum: IP Cameras
- Topic: New AD410 doorbell dies within 5 minutes
- Replies: 34
- Views: 22093
Re: New AD410 doorbell dies within 5 minutes
I did everything you said. I took the old Ezviz DB1C doorbell that works fine and took it off from the wiring. Then connected the Amcrest AD410 to the same wiring. The Amcrest does not start up even after a reset. It looks like it really died. Then connected the Ezviz DB1C again on the same wiring a...
- Sat Jul 17, 2021 4:56 am
- Forum: IP Cameras
- Topic: New AD410 doorbell dies within 5 minutes
- Replies: 34
- Views: 22093
Re: New AD410 doorbell dies within 5 minutes
How many volt of the usb micro is needed to start up the AD410?
- Sat Jul 17, 2021 2:46 am
- Forum: IP Cameras
- Topic: New AD410 doorbell dies within 5 minutes
- Replies: 34
- Views: 22093
Re: New AD410 doorbell dies within 5 minutes
My chime transformer is a 24v ac https://www.vekto.nl/beltrafo-15va. There were two options in the app, one for a mechanical and one for a digital chime. I chose the digital chime. Used wires with hard core. I pressed the doorbell a few times after installation and then my phone went off nicely and ...
- Fri Jul 16, 2021 5:10 pm
- Forum: IP Cameras
- Topic: New AD410 doorbell dies within 5 minutes
- Replies: 34
- Views: 22093
New AD410 doorbell dies within 5 minutes
Specially imported an AD410 to the Netherlands / Europe and therefore had to pay a lot of import duties. This I had all for it, but the joy was quickly over because after installation, the doorbell died and it never went on again. I am very upset about this and assume that Amcrest will send me a new...