IP3M-941/IP2M-841E/IP3M-HX2 Firmware Release

Have some questions or having issues with your IP Camera(s), Post them here for the mods and other users to assist you with.
User avatar
Techie007
Posts: 29
Joined: Sat Sep 24, 2016 3:13 pm

Re: IP3M-941/IP2M-841E/IP3M-HX2 Firmware Release

Post by Techie007 »

Just noting that I have dozens of these cameras installed in commercial security systems, all upgraded to the latest firmware, and I am having none of these problems; the new firmware is better in every regard in my experience. I wish I could upgrade the IP2M-852 outdoor cameras to this level firmware too so they would be HTML5 compliant instead of requiring a browser plugin in order to see the video feed during configuration.
lemmy999
Posts: 16
Joined: Sat May 14, 2016 12:38 pm

Re: IP3M-941/IP2M-841E/IP3M-HX2 Firmware Release

Post by lemmy999 »

Odd that you seem to be the only person not having issues.
User avatar
Revo2Maxx
Site Admin
Posts: 3245
Joined: Sat Jun 15, 2019 3:05 pm

Re: IP3M-941/IP2M-841E/IP3M-HX2 Firmware Release

Post by Revo2Maxx »

@lemmy999 It is hard to say why some have issues and others don't.. While I am not sure if your 841 is an E aka POE or if yours is only the 841W or B it might be as I know the 2 machines are different and that is why they don't share the Same FW...

So while I can't say for sure.. I know I didn't upgrade my 841EB and still using 2.420.AC00.17.R, Build Date: 2017-03-22 Then one of my 841B I am using 2.250 from 2017 as well. The rest are using the new FW and sadly most of them have issues. While it isn't bad issue they are still issues...

Like from day one with the new FW of 2019 camera wakes up after a reboot with preset 1 not being where I set it and while it isn't everytime it reboots I would say maybe once or 2 times a month it will be off in la la land and found for a short time I thought I found the issue having Preset 3 set and after doing a Factory Reset and only setting up Preset 1 after about month I woke up one day and it was all off the map and when I looked at the presets it was from back before I did the FW from 19 to 2020 one and 4 presets that had been set were also back in it... So today it again reboot at 2am and looked it was right in place however when I checked the preset it was off in la la land to an area I have not set nor would I because it was facing curtain...
Try to Avoid CCA Networking Cables They are JUNK PERIOD!
Where there is Life there is Hope
James
Fleegle
Posts: 39
Joined: Tue Dec 10, 2019 4:21 pm

Re: IP3M-941/IP2M-841E/IP3M-HX2 Firmware Release

Post by Fleegle »

My (2) 941's seem to be fine on the 2019 release. Glad I dont have to have the chrome extension anymore to view via web gui. But they mainly stream to my NAS anyway, not often I go directly into them. And am using them wireless.
ISLewis
Posts: 2
Joined: Mon Jan 11, 2021 3:44 pm

Re: IP3M-941/IP2M-841E/IP3M-HX2 Firmware Release

Post by ISLewis »

Purchased 2 IP3M-941s a while back. Updated to the latest firmware and both became terribly unstable. Crashing almost anytime they were viewed. Went through the whole rma process. Refurb cams both with 20191219. Similarly unstable albeit not quite as bad and the PTZ presets are constantly either being reset or deleted. I'm done with this brand.
ISLewis
Posts: 2
Joined: Mon Jan 11, 2021 3:44 pm

Re: IP3M-941/IP2M-841E/IP3M-HX2 Firmware Release

Post by ISLewis »

Also, all 4 941s that I've had emit an unacceptable amount of RFI on 146.915MHz.
Post Reply